‘Custom Boat Parts’ Category

Finally!  After so many requests we have located springs for the Holder 14 centerboard.  I have been told they work perfectly.

Our price including shipping for these is $19.00Holder 14 Center Board Spring (640x485)

ATTENTION: If you live outside the lower 48 United States please contact us directly to discuss shipping options (i.e. Alaska/Hawaii/International).

We now have a stainless steel hold down clip for your Sunfish and other daggerboards

$11 including shipping cost.

ATTENTION: If you live outside the lower 48 United States please contact us directly to discuss shipping options (i.e. Alaska/Hawaii/International).

Beautiful mahogany Sunfish Daggerboard. Brand new! This is a custom made sunfish style daggerboard with feathered edges for improved hydrodynamic flow. This fits the Sunfish and may also fit other similar sailboats. The Daggerboard measures 9.5″ x 45 .5″ x 3/4″ and is made from one piece mahogany.  This board is the exact board currently included by the manufacturer in many of their recreational Sunfish.  I know this because I make them.  It must be held in place with clip, not included, like older boards.  Weighted board available at additional cost.  Contact us for more info.

The blade is finished with 3 coats of Interlux Spar Varnish.

I usually have these in stock

I promise you will like this one.

$159.00 plus shipping

ATTENTION: If you live outside the lower 48 United States please contact us directly to discuss shipping options (i.e. Alaska/Hawaii/International).

holder-rudder-003holder-rudder-008Here is a replacement kick up rudder assembly with mahogany rudder and tiller and aluminum cheek blocks.  Lines are used to raise and lower the rudder.   This is also available with the mechanical kick up mechanism similar to the original.  This can be seen on the Holder 14 rudder I have on this site.  Both options are the same price.  Please note that pintles will be installed at locations to match your boat.  Please contact me to verify locations as all boats do not have gudgeons in the same locations.

$345.00

Here is a nice replacement kick up rudder assembly for your Holder 14.  This one has a mahogany rudder and tiller, aluminum cheek plates, and a stainless steel kick up rod.  It is designed very similar to the original equipment.  I have shown two pictures of a cut away of the assembly to show the mechanism.  Some people prefer to use lines to lift and hold down the rudder.  I can do this too.  A good example of this is shown on the Holder 12 item on this site.  I finish the wood with a minimum of 3 coats of Interlux spar varnish.  Pintles will be installed at locations to match your boat.  Please contact me to verify locations as all boats do not have gudgeons in the same locations.

$345.00

Here is a nice mahogany daggerboard to fit your Holder or Vagabond 14 boat.   This board has a better hydrodynamic foil shape than the original.  We have delivered many of these to happy customers.  I know you’ll like this one.  Finished with  minimum of 3 coats of Interlux spar varnish.  Other finishes available also.  Just contact us for further info.

$169.00 plus shipping.

WEST WIGHT POTTER 15 TILLERHere is a nice replacement tiller for your Potter 15.  It is laminated from beautiful ash and either black walnut or mahogany and then coated with a minimum of 3 coats of Interlux spar varnish.  This is typically shipped with no holes drilled for attachment.  I can do this for you at no charge.  Just give me your requirements.  Measure the thickness of your current tiller or rudder head.  I have seen both 1  1/8″ and 1  1/4″.

$99.00

We also now offer sunbrella tiller covers.  Check them out http://www.jowoodworks.com/archives/boat-parts/953

ATTENTION: If you live outside the lower 48 United States please contact us directly to discuss shipping options (i.e. Alaska/Hawaii/International).

Here is a nice wood kick up rudder assembly for your Potter 15.  The rudder is made from solid mahogany and will work perfectly for you.  The cheek and head assembly is made from aluminum.  Stainless steel is also available at an increased cost.  The rudder is coated with a minimum of 3 coats of spar varnish.  The tiller is laminated from ash and mahogany and then covered with a minimum of 3 coats of spar varnish.   I do include pintles with you verifying sizes and locations.  $425.00

We now also offer sunbrella tiller covers. Check them out.  http://www.jowoodworks.com/archives/boat-parts/953

DAYSAILER BOOM SUPPORTThis is the perfect addition to your boat.  Put this at the aft end of the cockpit to support the boom and now it will be possible to use a boom tent.  Protected with a minimum of 3 coats of spar varnish.

I usually have these in stock and ready to ship out

$60.00

ATTENTION: If you live outside the lower 48 United States please contact us directly to discuss shipping options (i.e. Alaska/Hawaii/International).

MONTGOMERY 17 TILLERBeautiful Tiller for the Montgomery 17 laminated from ash and mahogany.  Finished with a minimum of 3 coats of spar varnish.   Typically I do not drill the holes in the tiller but upon request they can be drilled to your specifications at no charge.  Just let me know.

$99.00

We now also offer sunbrella tiller covers. Check them out.  http://www.jowoodworks.com/archives/boat-parts/953

ATTENTION: If you live outside the lower 48 United States please contact us directly to discuss shipping options (i.e. Alaska/Hawaii/International).

Page 1 of 41234