‘Available Online’ Category

August 10th, 2010

QUICK CANOE KIT

The Quick Canoe is now ready for you.  This is one of the easiest boats there is to build.  Our kit consists of all the wooden parts you will need to put this together.  All you need is glue, some epoxy, a little fiberglass tape, a few screws, and paint.  We even include the wire ties to keep the bow and stern together while assembling.   The other ingredient is YOU, having a great time on the water in the canoe.  You will need very few tools for this.  A simple handsaw can be used for all cuts necessary although a jig saw is helpful.  A cordless drill would be good but you could do it with a hand screwdriver if necessary.  Duct tape and a few spring clamps will help with assembly.  All parts are labeled so you will know exactly what they are and the labels have dimensions on them just in case a label should come off.  This is the perfect quick and easy family project.  Everybody can help and the kids can tell their friends what they did!!   

Now for the technical stuff.  The basic hull comes in two pieces for the bottom and four for the sides. 

The gunwales, inwales and keel come in three pieces each.  The center piece of each is scarfed on both ends and the other pieces on one end.  We will include a piece of aluminum angle that will work as a clamping jig for the scarfs.  Be sure and cover this with plastic tape to prevent the wood sticking to the aluminum.  I recommend starting the gluing process early on so that all pieces will be glued by the time you need them for construction into the boat.

The skeg pieces will fit your boat perfectly prior to applying the keel.  After it is all glued up you can cut it to any final shape you would like.  A gentle curve works well.

There are five pieces for each seat.  All except the framing pieces are cut to fit.  The seat supports are ready for the installation of the framing.  No intricate cuts are required.

Believe me.  It doesn’t get any easier than this!!!

BASIC KIT WITH EXTERIOR PINE Including complete bound set of plans $435 plus shipping 

Marine fir, okoume, and miranti also available at additional cost.  I do not believe this should be necessary for this particular boat.

Many have already bought the plans from them so we keep them separate.  The next post on the site does not include plans.  Please go here for purchase of  canoe kit without plans.  http://www.jowoodworks.com/archives/available-online/666

We also have an epoxy and fiberglass kit available for the canoe.  Click here for more information .   http://www.jowoodworks.com/archives/available-online/671

You can read some discussion about the canoe building on Michael Storer’s site http://www.storerboatplans.com/wp/?cat=448

August 10th, 2010

Quick Canoe Kit Without Plans

The Quick Canoe is now ready for you.  This is one of the easiest boats there is to build.  Our kit consists of all the wooden parts you will need to put this together.  All you need is glue, some epoxy, a little fiberglass tape, a few screws, and paint.  We even include the wire ties to keep the bow and stern together while assembling.   The other ingredient is YOU, having a great time on the water in the canoe.  You will need very few tools for this.  A simple handsaw can be used for all cuts necessary although a jig saw is helpful.  A cordless drill would be good but you could do it with a hand screwdriver if necessary.  Duct tape and a few spring clamps will help with assembly.  All parts are labeled so you will know exactly what they are and the labels have dimensions on them just in case a label should come off.  This is the perfect quick and easy family project.  Everybody can help and the kids can tell their friends what they did!!   

Now for the technical stuff.  The basic hull comes in two pieces for the bottom and four for the sides. 

The gunwales, inwales and keel come in three pieces each.  The center piece of each is scarfed on both ends and the other pieces on one end.  We will include a piece of aluminum angle that will work as a clamping jig for the scarfs.  Be sure and cover this with plastic tape to prevent the wood sticking to the aluminum.  I recommend starting the gluing process early on so that all pieces will be glued by the time you need them for construction into the boat.

The skeg pieces will fit your boat perfectly prior to applying the keel.  After it is all glued up you can cut it to any final shape you would like.  A gentle curve works well.

There are five pieces for each seat.  All except the framing pieces are cut to fit.  The seat supports are ready for the installation of the framing.  No intricate cuts are required.

Believe me.  It doesn’t get any easier than this!!!

BASIC KIT WITH EXTERIOR PINE $375 plus shipping  plans not included.

Marine fir, okoume, and miranti also available at additional cost.  I do not believe this should be necessary for this particular boat.

Please note that this kit does not include plans.  It is posted for people that have already bought the plans.      If you need the kit with plans go here.  http://www.jowoodworks.com/archives/available-online/614

We also have an epoxy and fiberglass kit available for the canoe.  Click here for more information .  http://www.jowoodworks.com/archives/available-online/671

You can read some discussion about the canoe building on Michael Storer’s site http://www.storerboatplans.com/wp/?cat=448

We now have available a kit for the Quick Canoe including all the epoxy, filler, and fiberglass tape you will need to build the Quick Canoe.

Included in the kit is  3 qt Marinepoxy

                                            5 lb. Wood Flour

                                            50 l.f. 3″ Fiberglass Tape

This is enough of all items to build the complete canoe with filleting on the inside.  If you desire to tape both inside and out or cover the entire boat in epoxy then more material will be needed.  We can supply this too just let us know what you need and we will get it all for you.

Quick Canoe Epoxy kit including shipping  $99.00

February 9th, 2010

Holder 12 Rudder Assembly

holder-rudder-003holder-rudder-008Here is a replacement kick up rudder assembly with mahogany rudder and tiller and aluminum cheek blocks.  Board is weighted to help with holding it down.  Lines are used to raise and lower the rudder.   This is also available with the mechanical kick up mechanism similar to the original.  This can be seen on the Holder 14 rudder I have on this site.  Both options are the same price.  Please note that pintles will be installed at locations to match your boat.  Please contact me to verify locations as all boats do not have gudgeons in the same locations.

$285.00

Here is a nice replacement kick up rudder assembly for your Holder 14.  This one has a mahogany rudder and tiller, aluminum cheek plates, and a stainless steel kick up rod.  It is designed very similar to the original equipment.  I have shown two pictures of a cut away of the assembly to show the mechanism.  Some people prefer to use lines to lift and hold down the rudder.  I can do this too.  A good example of this is shown on the Holder 12 item on this site.  I finish the wood with a minimum of 3 coats of spar varnish.  Pintles will be installed at locations to match your boat.  Please contact me to verify locations as all boats do not have gudgeons in the same locations.

$285.00

February 8th, 2010

O’day 25 Hatch Boards

Beautiful mahogany hatch boards for O’day 25.  Finished with a minimum of 4 coats of Cetol.  Other finishes and woods available.  Contact us for custom quote on your boat.  Please note that all hatches require a template furnished by boat owner as dimensions vary slightly from boat to boat.

$150  plus shipping

February 8th, 2010

O’Day 25 Rudder

Here is a nice replacement rudder for your O’Day 25 sailboat.  It is made from laminated cypress for a very strong and stable product.  I will drill as many or as few holes for hardware as you want.  Finished with a minimum of  3 coats of spar varnish.

$275.00

February 7th, 2010

West Wight Potter 15 Tiller

WEST WIGHT POTTER 15 TILLERHere is a nice replacement tiller for your Potter 15.  It is laminated from beautiful ash and either black walnut or mahogany and then coated with a minimum of 3 coats of spar varnish.  This is typically shipped with no holes drilled for attachment.  I can do this for you at no charge.  Just give me your requirements.

$79.00

Here is a nice wood kick up rudder assembly for your Potter 15.  The rudder is made from 3 layers of okoume laminated together and weighted internally to work perfectly for you.  The cheek and head assembly is also made from okoume finished with a minimum of 3 coats of spar varnish.  The rudder is coated first with epoxy for added strength and impact resistance and covered with a minimum of 3 coats of spar varnish.  The tiller is laminated from ash and either black walnut or mahogany and then covered with a minimum of 3 coats of spar varnish.  Pintles not included.

$275.00

February 6th, 2010

Daysailer Boom Support

DAYSAILER BOOM SUPPORTThis is the perfect addition to your boat.  Put this at the aft end of the cockpit to support the boom and now it will be possible to use a boom tent.  Protected with a minimum of 3 coats of spar varnish.

$50.00

Page 1 of 512345